International Research Journal of Innovations in Engineering and Technology - IRJIET International Open Access, Monthly, Peer Reviewed, Reputed Journal ISSN (online): 2581-3048

Impact Factor (2025): 6.9

DOI Prefix: 10.47001/IRJIET

Deformation Analysis of Desalinated Water Storage Tank Using Finite Element Method

Abstract

Deformation in a structure is something that is very likely to occur when the object is subjected to a loading that leads to a pressure on the object. The approach taken to determine the deformation of the cylindrical tank was carried out using the finite element method using Ansys 2020 R2 software with axial loads due to the roof and circumferential loads on the cylinder from wind forces. The cylindrical tank that was the object observed in the practical work field was found to be deformed due to the very high loading from the roof and also the result of re-welding due to the repair of defective welds after being examined by ultrasonic testing. This was investigated using the finite element method to determine if the loading experienced by the cylinder was the main cause of the deformation and it was found that the maximum deformation was so small that it was difficult to say that the main cause of the deformation was the loading. It is known that re-welding a metal will change the mechanical properties of the material to become softer, which is the main reason why the deformation of the tank occurred in the practical field.

Country : Indonesia

1 Achmad Widodo2 Toni Prahasto3 Ojo Kurdi4 Yan Calvin Hanggara

  1. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  2. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  3. Mechanical Engineering, Diponegoro University, Semarang, Indonesia
  4. Mechanical Engineering, Diponegoro University, Semarang, Indonesia

IRJIET, Volume 8, Issue 5, May 2024 pp. 135-141

doi.org/10.47001/IRJIET/2024.805021

Full Paper
Download

References

  1. S. Taşkaya, S. Taşkaya, S. Taskaya, and S. Taskaya, “Investigation of Static Structure Effect According to Axial Coordinates by Using Finite Element Method in Ansys Workbench Software of AISI 310 Austenitic Stainless Cylindrical Mode Investigation of Static Structure Effect According to Axial Coordinates by Using Finite Element Method in Ansys Workbench Software of AISI 310 Austenitic Stainless Cylindrical Model Steel,” Article in International Journal of Scientific and Engineering Research, vol. 2, no. 11, pp. 65–70, 2018, doi: 10.5281/zenodo.2538535.
  2. N. Rathinam, B. Prabu, and N. Anbazhaghan, “Buckling analysis of ring stiffened thin cylindrical shell under external pressure,” Journal of Ocean Engineering and Science, vol. 6, no. 4, pp. 360–366, Dec. 2021, doi: 10.1016/j.joes.2021.03.002.
  3. D. Kowalski, “Stresses In The Tank Shell With Shape Deformation,”International Conference on Design, Inspection, Maintenance and Operation Of Cylindrical Steel Tanks and Pipelines. 2003.
  4. M. I. Elso, “Finite Element Method studies on the stability behavior of cylindrical shells under axial and radial uniform and non-uniform loads made in Department of Mechanical and Process Engineering Hochschule Niederrhein presented by Summary of the Final Project Work Project Title: Finite Element Method studies on the stability behavior of cylindrical shells under axial and radial uniform and non-uniform loads,” 2012.
  5. M. Rastgar and H. Showkati, “Buckling behavior of cylindrical steel tanks with concavity of vertical weld line imperfection,” J Constr Steel Res, vol. 145, pp. 289–299, Jun. 2018, doi: 10.1016/j.jcsr.2018.02.028.
  6. S.-E. Kim and C.-S. Kim, “Buckling strength of the cylindrical shell and tank subjected to axially compressive loads,” 2002. [Online]. Available: www.elsevier.com/locate/tws
  7. F. P. (Ferdinand P. Beer, Mechanics of materials. McGraw-Hill, 2011.
  8. L. Skinner, “Introduction,” in Hydraulic Rig Technology and Operations, Elsevier, 2019, p. xxi. doi: 10.1016/b978-0-12-817352-7.09989-9.
  9. L. W. Mckeen et al., “FATIGUE AND TRIBOLOGICAL PROPERTIES OF PLASTICS AND ELASTOMERS Third Edition.”
  10. N. Fatchurrohman and S. T. Chia, “Performance of hybrid nano-micro reinforced mg metal matrix composites brake calliper: Simulation approach,” in IOP Conference Series: Materials Science and Engineering, Institute of Physics Publishing, Nov. 2017. doi: 10.1088/1757-899X/257/1/012060.
  11. S. Tunde Azeez and P. Madindwa Mashinini, “Radiography examination of friction stir welds of dissimilar aluminum alloys,” Mater Today Proc, vol. 62, pp. 3070–3075, Jan. 2022, doi: 10.1016/j.matpr.2022.03.225.
  12. M. Ben Gharsallah and E. Ben Braiek, “Weld inspection based on radiography image segmentation with level set active contour guided off-center saliency map,” Advances in Materials Science and Engineering, vol. 2015, 2015, doi: 10.1155/2015/871602.

Copyright @ 2026-2017 IRJIET. All Right Reserved.

Developed by Byzero Technologies